For pallet and grain transport etc.

Weights

Gross weight (techn.): 27 t
Gross weight (perm.): 24 t
Payload: approx. 18 t
Tare weight: approx. 5. 8 t

Dimensions

Internal length: approx. 8,500 mm
Internal width: approx. 2,460 mm
Total width: 2,550 mm
Loading height, unladen: approx. 1,390 mm

Frame

Naxtra welded steel frame construction – low design height
Connector lock for tipper body with cross-over protection

Chassis

Air suspension with autom. lowering device via inductive switch

Low-maintenance air-sprung axles with 430 mm disc brakes,
each with 9 t axle load

Tyres :
6 x 385/65 R 22.5 160J, manufacturer as per factory specifications
6 steel wheel rims 11.75 x 22.5, 10-hole, 120 mm rim offset, silver

Drawgear

Fixed drawbar , 40 mm drawbar eye
, with silent bushing and drawbar locking device

Brake system

Brake system according to EC Directive 71/320 or ECE R13
Two-line brake
Spring-loaded parking brake on 2nd and 3rd axles
EBS – electronic brake system
Wabco 4S3M = 1st and 3rd axles sensed
RSS – stability program
Steel air tank

Tipping system

1 tipper cylinder for 3-way tipping, approx. 40 t initial lifting force,
1 arrester cable
Rearward tipping angle: approx. 38°
1-pipe system with hydraulic connecting hose incl.
plug-in coupling NW13, without truck attachments

Tipping loading ramp

Full-steel welded construction with fine-grained special steel floor panels, 5 mm
(slight floor unevenness possible due to weld distortion)

Side walls

Grain-tight side wall mounting with labyrinth sealing system
Fixed steel plate front wall, 3 mm, approx. 980 mm high
2-part aluminium hollow profile side walls, 40 mm, approx. 980 mm high,
(top and bottom profiles reinforced 4/2 mm, 3 x 200 mm intermediate profiles 2/2 mm), with vertical special sealing groove, without bracket recess, foldable
with extended swivel bolt locks and spring lifting aid, hinged with man. central locking (operated separately for each wall)
Aluminium hollow profile rear wall, 40/2/2 mm, approx. 980 mm high,
foldable with extended swivel bolt locks and hinged with man. central locking

Posts

2 fixed front corner posts, integrated in front wall
2 foldable centre posts, in side wall height
2 fixed rear corner posts, welded to sides, in side wall height
Tension chain with fastener for centre posts

Electrical equipment

24 V lighting system according to EC Directive 76/756/EWG
2 seven-chamber tail lights
LED side marker lights
2 clearance lamps
2 contour lights
Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector

Paintwork

Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black

Reflective contour marking strips across entire length of sides and all-round contour marking at rear (white on sides and red at rear by default), according to ECE 48

Accessories

Rear markings as per ECE standards

Attachments

Wheel chock(s) as per regulations
Noise dampers
Single wheel plastic mudguards with spray protection as per regulations
Side impact protection made from aluminium profiles as per regulations, coated black
Fixed aluminium trapezoidal underride protection, unpainted
1 spare wheel bracket for 1 spare wheel
Tarpaulin hooks on hinges